John Holguin
If you have an iPhone 6s and are experiencing issues with the front facing camera, you may need to remove it in order to diagnose or replace the faulty component. The front facing camera is responsible for selfies, video calls, and Face ID, so it’s important to ensure it is functioning properly. Removing the front facing camera on your iPhone 6s requires careful handling and attention to detail, but can be done with a few simple tools and steps.
Before you begin, it’s important to note that removing the front facing camera from your iPhone 6s may void any warranty or insurance coverage you have. If your device is still under warranty, it’s recommended to contact Apple or an authorized service provider for assistance. However, if you’re comfortable with DIY repairs and are out of warranty, you can proceed with caution.
To remove the front facing camera on your iPhone 6s, you’ll need a few tools: a small Phillips screwdriver, a plastic pry tool or an opening tool, and a pair of tweezers. It’s also recommended to have a clean and well-lit workspace to prevent any small components from getting lost. Once you have your tools ready, follow these steps to take the front facing camera off:
- Power off your iPhone 6s completely and disconnect it from any power source.
- Use the small Phillips screwdriver to remove the two screws located on either side of the front facing camera module.
- Gently insert the plastic pry tool or opening tool into the small gap between the front facing camera and the front panel of the iPhone.
- Apply gentle pressure and carefully pry up the front facing camera module, being mindful not to damage any of the surrounding components.
- Once the front facing camera module is slightly lifted, use the pair of tweezers to disconnect the cable connecting it to the iPhone’s logic board.
- With the cable disconnected, you can now fully remove the front facing camera module from the iPhone 6s.
When reassembling your iPhone 6s after removing the front facing camera, be sure to follow the steps in reverse order. Take care to align the front facing camera module properly before inserting the screws and tightening them securely, but not too tight. It’s always a good idea to test the functionality of the camera before fully reassembling your iPhone.
If you encounter any difficulties during the process or are unsure about any steps, it’s best to seek professional assistance. Removing and replacing components in electronic devices requires a certain level of skill and expertise to avoid causing further damage. Be cautious and take your time, and with the right tools and knowledge, you’ll be able to successfully remove the front facing camera on your iPhone 6s.
Removing the iPhone 6S Front Facing Camera: A Step-by-Step Guide
The front facing camera on your iPhone 6S is an essential feature for taking selfies and making video calls. However, if it becomes damaged or starts malfunctioning, you may need to remove and replace it. This step-by-step guide will walk you through the process of safely removing the front facing camera on your iPhone 6S.
What you’ll need:
- Small screwdriver set
- Plastic opening tool
- Suction cup
- Tweezers
Step 1: Power off your iPhone 6S and remove the two small screws located on either side of the charging port using the small screwdriver.
Step 2: Place the suction cup near the home button and gently pull upward to create a small gap between the display assembly and the rear case.
Step 3: Insert the plastic opening tool into the gap and carefully slide it around the edges of the display assembly to loosen the adhesive.
Step 4: Lift the display assembly up and support it at a slight angle with the help of a small stand or a stack of books.
Step 5: Locate the front facing camera module at the top of the device.
Step 6: Use the tweezers to disconnect the ribbon cable attached to the front facing camera module.
Step 7: Gently lift the front facing camera module out of its housing.
Step 8: To install a new front facing camera module, simply follow these steps in reverse order.
Important note: If you are not comfortable performing these steps on your own, it is recommended to seek professional assistance or take your iPhone 6S to an authorized repair center.
By following this step-by-step guide, you can safely remove the front facing camera on your iPhone 6S and replace it with a new one if needed. Remember to handle all the components with care and take your time during the process to avoid any damage to your device.
Tools You Will Need for Removing the iPhone 6S Front Facing Camera
Removing the front facing camera on an iPhone 6S is a delicate task that requires the right tools. Here are the tools you will need to successfully complete the job:
- Small Phillips head screwdriver
- Plastic opening tool
- Suction cup
- Tweezers
- Adhesive strips or double-sided tape
The small Phillips head screwdriver is essential for removing the screws that secure the front facing camera in place. It is important to use the correct size screwdriver to avoid damaging the screws or the surrounding components.
A plastic opening tool is necessary for prying apart the front panel and accessing the front facing camera. This tool is designed to safely separate the delicate components without causing any damage.
A suction cup will be helpful in lifting the front panel away from the device. This allows for easier access to the front facing camera and prevents any accidental damage during the removal process.
Tweezers are useful for handling smaller components and connectors with precision. They can be used to carefully disconnect any cables or connectors attached to the front facing camera.
Adhesive strips or double-sided tape are needed to reattach the front facing camera when the replacement or repair is completed. These adhesive materials ensure a secure and stable connection between the camera and the device.
With these tools at your disposal, you can confidently remove the front facing camera of your iPhone 6S. Remember to exercise caution and take your time to ensure a successful repair or replacement.
Step 1: Power off Your iPhone 6S
The first step in removing the front facing camera on your iPhone 6S is to power off the device. This is an important safety precaution to ensure that you don’t accidentally damage any internal components while working on your phone.
To power off your iPhone 6S:
- Press and hold the power button, located on the right side or top of your device, depending on your model.
- After a few seconds, a slider will appear on the screen.
- Swipe the slider from left to right to power off your device.
Once your iPhone 6S is powered off, you can proceed to the next step in removing the front facing camera.
Step 2: Remove the Display Assembly
Before removing the front facing camera of your iPhone 6s, you will need to detach the display assembly.
To do this, follow the steps below:
1. Power off your iPhone
First, you need to power off your iPhone 6s. Press and hold the power button until the “slide to power off” option appears on the screen. Slide it to power off your device.
2. Remove the two screws at the bottom of the iPhone
Using a pentalobe screwdriver, remove the two screws located at the bottom of your iPhone 6s, on either side of the charging port.
3. Lift the display assembly
Take a suction cup and place it near the home button of your iPhone. Gently pull up on the suction cup to create a small gap between the display assembly and the rear case.
Insert a plastic opening tool or a razor blade into the gap you created, and slowly slide it along the bottom edge of the iPhone to loosen the adhesive.
Once the adhesive is loosened, carefully lift the display assembly, starting from the bottom edge, to about a 90-degree angle. Be careful not to disconnect the display cables at this point.
4. Disconnect the display cables
With the display assembly lifted, you will now have access to the connectors that attach the display cables to the logic board.
Use a spudger or a plastic opening tool to carefully disconnect the display cables by prying up the connectors. Start with the home button connector, then disconnect the display and digitizer cable connectors.
Once the display cables are disconnected, you can set aside the display assembly, as it is no longer attached to the iPhone.
Note: Be extra cautious when working with the display assembly, as it is fragile and can easily be damaged.
Step 3: Disconnect the Front Facing Camera Flex Cable
Once you have removed the display assembly and battery, you can now proceed to disconnecting the front facing camera flex cable. Follow the steps below:
- Locate the front facing camera flex cable, which is connected to the logic board. It is a small, thin cable attached to a connector.
- Using a plastic spudger or a small non-metal prying tool, carefully lift the connector latch for the front facing camera flex cable. This will release the cable from its socket on the logic board.
- Gently pull the cable away from the socket, ensuring that you do not damage the cable or the connector. Take your time and be patient.
- Once the cable is disconnected, you can set it aside and proceed with further repairs or replacement.
It is important to handle the front facing camera flex cable with care, as it is delicate and can be easily damaged. Avoid using excessive force when removing or disconnecting the cable to prevent any unnecessary damage.
Note: If you are replacing the front facing camera, make sure to transfer over any necessary components from the old camera to the new one, such as the proximity sensor or ambient light sensor.
Step 4: Remove the Front Facing Camera Bracket
Now that you have disconnected the front facing camera cable, it’s time to remove the bracket that is holding the camera in place.
Start by locating the two small Phillips screws that are securing the bracket to the iPhone 6s.
Using a Phillips screwdriver, carefully unscrew and remove the screws.
Once the screws are removed, gently lift the bracket off the iPhone.
Caution:
Be careful not to damage any other components as you remove the bracket. It is important to handle the bracket and screws with care to avoid any mishaps.
Tip:
You can use a pair of tweezers or a plastic spudger to help lift the bracket if needed.
Set the bracket aside in a safe place, as you will need it later when reassembling the iPhone 6s.
Step 5: Take Off the Front Facing Camera
Before proceeding with this step, make sure you have completed all the previous steps and have gathered the necessary tools.
1. Start by disconnecting the front facing camera flex cable. Gently lift the cable connector upwards using a plastic spudger or tweezers. Be careful not to apply too much force, as it can damage the connector.
2. Once the flex cable is disconnected, you can now remove the front facing camera module. Use a screwdriver to remove the screws securing the camera in place.
3. Gently lift the camera module out of its housing. Be cautious not to touch the lens or any other delicate parts, as it can cause damage.
4. Inspect the front facing camera for any signs of damage or dirt. If necessary, clean it using a microfiber cloth and gentle cleaning solution.
5. Before reassembling, make sure the camera module is aligned correctly with its housing. Carefully place the module back into its designated spot.
6. Secure the camera in place by tightening the screws with a screwdriver.
7. Reconnect the front facing camera flex cable by firmly pressing it down into the connector until it clicks into place.
8. Congratulations! You have successfully taken off the front facing camera of your iPhone 6s. Now you can proceed with any necessary repairs or replacements.
Step 6: Inspect and Clean the Camera Area
Before reassembling your iPhone 6s front facing camera, it’s important to inspect the area around the camera for any dirt, debris, or smudges. This will ensure that your camera is able to capture clear and sharp images.
Here are the steps to clean the camera area:
- Start by using a soft, lint-free cloth to gently wipe the camera lens. This will remove any fingerprints or smudges that may be affecting the image quality.
- If there is stubborn dirt or debris around the camera lens, you can use a microfiber cloth slightly dampened with water or isopropyl alcohol. Be careful not to use too much liquid.
- Gently wipe the camera lens and the surrounding area with the damp cloth, being cautious not to apply excessive pressure.
- Inspect the camera area for any remaining dirt or debris. If necessary, you can use a soft-bristled brush or a can of compressed air to gently remove any particles.
- Once the area is clean, use a dry cloth to remove any moisture or residue leftover from the cleaning process.
After cleaning the camera area, you can proceed with the reassembly process, following the previous steps in reverse order. Make sure to handle the camera module with care to avoid any accidental damage.
By regularly cleaning the camera area, you can ensure that your iPhone 6s front facing camera continues to capture high-quality photos and videos.
Step 7: Install the New Front Facing Camera
Now that you have removed the old front facing camera, it’s time to install the new one. Follow these steps:
- Take the new front facing camera and align it with the opening on the front of the iPhone 6s.
- Make sure that the connectors on the camera align with the corresponding connectors on the iPhone.
- Gently press the camera into place until it is securely seated.
- Double-check that the camera is aligned properly and flush with the front of the iPhone.
- Reconnect the two ribbon cables by carefully aligning them with their respective connectors on the logic board.
- Press the connectors down until they are firmly in place.
- Replace the metal shield that covers the camera connectors, making sure it is secured with screws or adhesive if necessary.
- Reassemble the iPhone by following the previous steps in reverse order.
Important:
Be cautious when handling the front facing camera and its connectors, as they are fragile. Take your time to align them properly to avoid causing any damage. If you encounter any difficulties during the installation process, consider seeking professional assistance.
Step 8: Reassemble Your iPhone 6S
Once you have successfully removed and replaced the front facing camera on your iPhone 6S, it is time to reassemble the device. Follow these steps to ensure a proper reassembly:
- Take the front panel assembly and carefully position it over the display assembly.
- Gently press down on the front panel assembly to secure it in place.
- Reinsert the five screws that secure the front panel assembly to the rear case.
- Use a pentalobe screwdriver to tighten the screws.
- Reconnect the display cable connector to the logic board.
- Gently press down on the connector until it clicks into place.
- Reattach the front panel assembly cable bracket.
- Reinsert the three screws that secure the bracket.
- Reconnect the front facing camera cable to the logic board.
- Gently press down on the connector until it snaps into place.
- Reattach the earpiece speaker assembly cable to the logic board.
- Gently press down on the connector until it clicks into place.
- Reinsert the two screws that secure the cable bracket.
- Reconnect the display assembly cable bracket to the logic board.
- Gently press down on the bracket until it clicks into place.
- Reinsert the four screws that secure the bracket.
- Finally, carefully lower the display assembly onto the rear case and press firmly to ensure it is properly seated.
Once you have completed these steps, your iPhone 6S should be fully reassembled and ready to use with the new front facing camera.
