John Holguin
If you own an iPhone 6s Plus and notice that the rear camera glass is cracked or shattered, don’t worry! Replacing the rear camera glass on your iPhone is a relatively simple process that you can do at home with just a few tools. This guide will walk you through the steps to replace the rear camera glass on your iPhone 6s Plus, allowing you to restore the functionality and aesthetics of your device.
Step 1: Gather the necessary tools
Before you begin, make sure you have all the necessary tools for the job. You will need a small screwdriver, a heat gun or hairdryer, a suction cup, and a replacement rear camera glass. You can find these tools online or at your local electronics store.
Step 2: Remove the rear camera
To replace the rear camera glass, you will first need to remove the rear camera from your iPhone. Start by powering off your device and removing the SIM card tray. Then, use the small screwdriver to remove the screws around the camera module. Once the screws are removed, carefully lift the camera module from the device.
Step 3: Heat and remove the broken glass
Next, use the heat gun or hairdryer to warm up the rear camera glass. This will soften the adhesive and make it easier to remove. Once the glass is heated, use the suction cup to gently pull the broken glass away from the camera module. Be careful not to apply too much force to avoid damaging the camera or other components.
Step 4: Install the replacement glass
Now it’s time to install the replacement rear camera glass. Start by cleaning any residue or adhesive from the camera module using a microfiber cloth or alcohol wipes. Then, carefully peel off the adhesive backing from the replacement glass and align it with the camera module. Press firmly to ensure a secure bond.
Step 5: Reassemble and test
Once the replacement glass is securely attached to the camera module, reassemble your iPhone by following the steps in reverse order. Make sure to tighten the screws properly and insert the SIM card tray. Finally, power on your device and test the rear camera to ensure it is functioning correctly.
Please note that replacing the rear camera glass on your iPhone 6s Plus may void any existing warranty. If you are unsure or uncomfortable performing the repair yourself, it is recommended to seek professional assistance.
By following these simple steps, you can easily replace the rear camera glass on your iPhone 6s Plus and restore its functionality and appearance. With a few tools and a little patience, you can have your device looking as good as new in no time!
Step 1: Gather necessary tools
Before starting the process of replacing the rear camera glass on your iPhone 6s Plus, make sure you have all the necessary tools at hand. This will ensure that you are prepared and can complete the job smoothly.
What you will need:
- Replacement rear camera glass: You will need a new rear camera glass specifically designed for the iPhone 6s Plus. Ensure that the replacement glass is high-quality and compatible with your device.
- Small Phillips screwdriver: This tool is essential for removing the screws that hold the rear camera glass in place.
- Plastic pry tool: A plastic pry tool will help you safely and gently pry off the old camera glass without damaging the surrounding components.
- Cleaning cloth: You will need a soft cleaning cloth to wipe away any dust or debris from the camera lens and surrounding area.
- Adhesive: Depending on the replacement glass you are using, you may need adhesive to secure the new glass in place. Ensure that the adhesive is specifically designed for electronic devices.
Having all these tools ready before starting the process will save you time and make the replacement process much easier.
Step 2: Power off the device
Before starting the repair process, it is crucial to power off your iPhone 6s Plus. This will ensure your safety and prevent any damage to the device.
To power off the device, follow these steps:
- Press and hold the power button located on the right side of the device.
- Wait for the “slide to power off” option to appear on the screen.
- Slide the power icon from left to right to power off the iPhone.
Once the device is completely powered off, you can proceed with the next steps of replacing the rear camera glass. Make sure to handle the device with care and follow the instructions diligently to avoid any mishaps during the repair process.
Step 3: Remove the rear panel
Before starting this step, make sure that you have already removed the screws and clips from the previous steps.
| Tools needed: | – Pentalobe screwdriver – Plastic spudger – Heat gun or hairdryer |
1. Start by heating the rear panel of your iPhone 6s Plus using a heat gun or a hairdryer. This will soften the adhesive, making it easier to remove the panel.
2. Once the panel is heated, insert a plastic spudger into the gap between the rear panel and the frame of the iPhone. Gently pry the panel away from the frame.
3. Work your way around the edges of the rear panel, continuing to pry it away from the frame. Take your time and be careful not to apply too much pressure, as this could damage the panel or other internal components.
4. Once the panel is fully separated from the frame, carefully lift it away from the iPhone. Set it aside in a safe place.
5. With the rear panel removed, you now have access to the rear camera glass. Proceed to the next step to learn how to replace it.
Step 4: Disconnect the battery
Before you begin replacing the rear camera glass on your iPhone 6s Plus, it is important to disconnect the battery to prevent any accidental short circuits.
Follow these steps to disconnect the battery:
1. Gather the necessary tools
Make sure you have the following tools ready:
- Small Phillips screwdriver
- Plastic spudger
- Suction cup
- Tweezers
2. Power off your iPhone
Press and hold the power button until the “Slide to power off” slider appears. Slide it to the right to turn off your iPhone.
3. Unscrew the two outermost screws
Use the small Phillips screwdriver to unscrew the two screws located on either side of the Lightning port at the bottom of your iPhone.
4. Use the plastic spudger to gently pry up the display assembly
Insert the plastic spudger into the small gap between the display assembly and the rear case of your iPhone. Carefully pry up the display assembly, starting from the bottom and moving towards the top of the device.
5. Use the suction cup to lift the display assembly
Place the suction cup near the Home button and gently pull up, applying even pressure. This will help separate the display assembly from the rear case.
6. Remove the metal plate covering the battery connector
Use the Phillips screwdriver to remove the three screws securing the metal plate covering the battery connector. Set the screws aside for reassembly later.
7. Disconnect the battery connector
Use the plastic spudger to carefully disconnect the battery connector by prying it up from the motherboard. Make sure to lift the connector straight up to avoid damaging it.
With the battery disconnected, you can proceed to replace the rear camera glass on your iPhone 6s Plus without any risk of electrical damage.
Step 5: Remove the rear camera
Once the adhesive is soft, use a plastic spudger to gently pry up the rear camera module. Start from one side and work your way around until the module is completely detached from the adhesive. Be careful not to use too much force, as the camera module is fragile and can be easily damaged.
Once the rear camera module is free from the adhesive, use a pair of tweezers to carefully detach the camera cable connector from its socket on the logic board. Be gentle and make sure not to apply too much pressure as you disconnect the cable.
After disconnecting the camera cable, carefully lift out the rear camera module and set it aside.
Take note of any foam padding or other components that may be attached to the rear camera module and make sure to transfer them to the new camera module before installing it.
Now, you can proceed to the next step to install the new rear camera module.
Step 6: Replace the camera glass
Once you have removed the old camera glass, it’s time to install the new one. Here are the steps to do it:
- Carefully peel off the protective backing from the adhesive side of the new camera glass.
- Position the camera glass over the camera lens on the back of your iPhone 6s Plus and align it properly.
- Gently press down on the camera glass to secure it in place.
- Make sure there are no air bubbles or dust particles trapped under the camera glass.
Important tips:
- While aligning the camera glass, be cautious not to touch the camera lens to avoid fingerprints or smudges.
- To prevent any damage, apply gentle and even pressure while pressing down on the camera glass.
Now that you have successfully replaced the camera glass on your iPhone 6s Plus, you can proceed with reassembling the device.
Note: If you are unsure about undertaking this repair by yourself, it is recommended to seek professional assistance or take your device to an authorized service center.
Step 7: Reassemble the device
Once you have successfully replaced the rear camera glass on your iPhone 6s Plus, it’s time to reassemble the device. Follow these steps to put everything back together:
1. Line up the rear camera
Take the new rear camera glass and carefully align it with the camera lens on the back of the iPhone 6s Plus. Make sure it fits securely and is oriented correctly.
2. Attach the adhesive
Apply a small amount of adhesive around the edges of the camera glass. This will help secure it in place and prevent any dust or dirt from getting inside.
3. Reconnect the cables
Gently reconnect the cables for the rear camera and any other components that were disconnected during the disassembly process. Make sure they are properly aligned and firmly connected.
4. Replace the rear panel
Carefully put the rear panel back onto the iPhone 6s Plus, making sure it lines up with the edges of the device. Press down firmly to ensure a snug fit.
5. Secure the screws
Using the pentalobe screwdriver, tighten the screws that hold the rear panel in place. Be careful not to overtighten them, as this could damage the device.
6. Test the camera
Turn on your iPhone 6s Plus and test the rear camera to make sure it is functioning properly. Take a few photos and videos to ensure everything is working as expected.
7. Clean the device
Before using your iPhone 6s Plus, give it a final wipe-down with a clean, lint-free cloth to remove any smudges or fingerprints.
8. Done!
Congratulations! You have successfully replaced the rear camera glass on your iPhone 6s Plus. Your device should now be ready to use.
| Warning: | Be cautious while handling delicate components and small screws. Take your time and be gentle to avoid causing any damage to your device. |
|---|
Step 8: Power on the device
After successfully replacing the rear camera glass on your iPhone 6s Plus, it is time to power on the device and test the new camera.
Make sure that the battery is sufficiently charged to avoid any power interruptions during the startup process. Connect your device to a power source if needed.
To power on your iPhone 6s Plus, press and hold the power button located on the side of the device until the Apple logo appears on the screen. Release the button once you see the logo.
Allow the device to fully boot up and navigate to the camera app to test the rear camera. Take a few pictures and videos to ensure that the new camera glass is working properly.
If you encounter any issues with the camera or notice any abnormalities in the picture quality, ensure that the camera glass is properly aligned and attached. If necessary, repeat the previous steps or seek professional assistance.
Important points to consider:
- Make sure the device is powered off before attempting to replace the rear camera glass.
- Use caution when removing the old camera glass to avoid damaging the device or other components.
- Handle the new camera glass with clean, dry hands to prevent any smudges or fingerprints that could affect picture quality.
- Ensure that the camera app is up to date for optimal performance.
Note: If you are not confident in replacing the rear camera glass yourself, it is recommended to take your iPhone 6s Plus to a professional repair service to avoid any further damage to the device.
Troubleshooting tips
If you are experiencing any issues while replacing the rear camera glass on your iPhone 6s Plus, here are some troubleshooting tips that may help:
1. Check for proper alignment
Ensure that the new camera glass is aligned properly with the camera module. It should fit snugly and not protrude or sit unevenly.
2. Clean the camera lens
Before replacing the glass, make sure to clean the camera lens thoroughly. Any dirt or smudges on the lens can affect the picture quality. Use a microfiber cloth or lens cleaning solution to gently wipe the lens clean.
3. Restart your iPhone
If you are still experiencing issues after replacing the camera glass, try restarting your iPhone. This can help reset any software glitches or conflicts that may be causing the problem.
4. Update your iOS
Make sure that your iPhone is running the latest version of iOS. Software updates often include bug fixes and improvements that can help resolve camera-related issues.
5. Contact professional help
If none of the above troubleshooting tips resolve the issue, it may be best to seek professional help. An Apple Authorized Service Provider or a qualified technician will be able to diagnose and fix any hardware or software issues with your iPhone’s rear camera.
By following these troubleshooting tips, you should be able to address any issues that may arise during the replacement of the rear camera glass on your iPhone 6s Plus.
FAQ
Where can I buy a replacement rear camera glass for iPhone 6s Plus?
You can buy a replacement rear camera glass for iPhone 6s Plus from various online retailers or electronics stores. Some popular places to look for these replacement parts include Amazon, eBay, and electronics repair shops. Make sure to choose a reputable seller and check for compatibility with your specific iPhone model before making a purchase.
Do I need any special tools to replace the rear camera glass on iPhone 6s Plus?
Yes, you will need some special tools to replace the rear camera glass on iPhone 6s Plus. The necessary tools include a small suction cup, a plastic spudger, a small Phillips screwdriver, and a guitar pick or thin plastic card. These tools will help you remove the necessary screws and cables without causing any damage to the device. It is important to use the right tools for the job to ensure a successful repair.
Can I replace the rear camera glass on iPhone 6s Plus myself, or should I take it to a professional?
It is possible to replace the rear camera glass on iPhone 6s Plus yourself if you feel comfortable and have some experience with electronics repairs. However, it is a delicate process that requires patience and precision. If you are unsure or inexperienced, it is recommended to take your iPhone to a professional repair service. They will have the necessary tools and expertise to safely replace the camera glass and ensure that everything is working correctly.
