John Holguin
Accidents happen, and if you find yourself with a cracked or broken rear camera glass on your iPhone 5s, don’t worry! You don’t have to replace the entire phone or spend a fortune at the Apple store. With a little bit of patience and the right tools, you can easily replace the rear camera glass yourself.
Before you begin, make sure you have the necessary tools: a small Phillips screwdriver, a suction cup, a spudger or plastic opening tool, and a replacement rear camera glass piece. You can find these tools online or at a local electronics store. It’s also a good idea to have a clean and well-lit workspace.
Start by turning off your iPhone 5s and removing the two small Phillips screws located next to the charging port. Use the suction cup to gently lift the screen away from the body of the phone. Be careful not to lift it too high or you may damage the cables connecting the screen to the rest of the phone. Use the spudger or plastic opening tool to carefully disconnect the cables and set the screen aside.
With the screen removed, you’ll see the rear camera glass located at the top of the phone. Use the spudger or plastic opening tool to carefully pry it out. Be gentle, as the glass is fragile and can easily break further. Once the old glass is removed, take your replacement piece and carefully snap it into place. Make sure it’s securely in position before moving on.
Now, reattach the screen cables and place the screen back onto the body of the phone. Press down firmly, making sure it’s properly aligned, and then reinsert the two Phillips screws next to the charging port. Turn on your iPhone 5s and test the rear camera to ensure it’s working properly.
Congratulations! You’ve successfully replaced the rear camera glass on your iPhone 5s. With a little bit of time and effort, you can save yourself the cost and hassle of getting it repaired professionally. Remember to take your time and be careful throughout the process, and soon enough, your iPhone 5s will be as good as new!
Please review carefully before attempting any repair.
Replacing the rear glass camera piece on an iPhone 5s requires delicate handling and precision. It is important to understand the process fully before attempting the repair to avoid causing any additional damage to your device. Here are some key points to consider:
- Ensure that you have the necessary tools for the repair, such as a pentalobe screwdriver, suction cup, and tweezers.
- Take your time and work in a clean, well-lit area to avoid losing any small screws or components.
- Follow a detailed guide or tutorial specific to the iPhone 5s model to ensure you are following the correct steps.
- Exercise caution when using tools to prevent scratching or damaging the surrounding areas of the device.
- Disconnect the battery before starting the repair to avoid any potential electrical damage.
- If you feel unsure about any step or encounter any difficulties, consider seeking professional assistance instead of continuing the repair.
By reviewing these points and understanding the importance of careful handling, you will be better prepared to successfully replace the rear glass camera piece on your iPhone 5s.
Step 1: Gather the necessary tools and materials
Before you start replacing the rear glass camera piece on your iPhone 5s, you will need to gather the necessary tools and materials. Make sure you have the following items:
- Replacement rear glass camera piece: You can purchase this online or from a local phone repair shop.
- Small Phillips screwdriver: This will be used to remove the screws on the iPhone.
- Plastic opening tool: This tool will help to pry open the iPhone without damaging the delicate parts.
- Adhesive tape or adhesive glue: You will need this to secure the new rear glass camera piece in place.
- Tweezers: These will be useful for handling small parts and connectors.
- Precision knife or blade: This may be needed to gently remove any adhesive or old glass remaining on the iPhone.
- Cleaning cloth: To clean the iPhone and ensure a clean surface for the new rear glass camera piece.
Make sure to have all these tools and materials ready before you begin the replacement process. This will help you complete the repair smoothly and efficiently.
Step 2: Power off the iPhone 5s
Before you begin replacing the rear glass camera piece on your iPhone 5s, it’s important to power off the device to avoid any potential electrical shocks or damage to the components.
To power off your iPhone 5s, follow these steps:
- Press and hold the power button located on the top right corner of your iPhone.
- A slider will appear on the screen that says “slide to power off.” Slide the button from left to right to power off the device.
- Wait for a few seconds as the iPhone shuts down completely.
Once your iPhone is powered off, you can proceed with the next steps to replace the rear glass camera piece on your iPhone 5s.
Step 3: Remove the rear panel
Before you begin, make sure you have the necessary tools, including a small Phillips screwdriver and a plastic opening tool. Follow the steps below to remove the rear panel:
- Power off your iPhone 5s and remove the SIM card tray.
- Locate the two Pentalobe screws at the bottom of the device.
- Using the small Phillips screwdriver, unscrew the two Pentalobe screws and set them aside.
- Place the plastic opening tool in the gap between the rear panel and the aluminum frame.
- Gently pry the rear panel upwards, starting from the bottom.
- Continue prying the rear panel around the edges until it is completely detached from the frame.
- Carefully lift and remove the rear panel, making sure not to damage any of the internal components.
With the rear panel removed, you will now have access to the internal components of your iPhone 5s, including the rear glass camera piece that you wish to replace.
Step 4: Disconnect the camera cables
Before proceeding, disconnecting the camera cables is an essential step to ensure no damage is caused during the replacement process. Follow the steps below to disconnect the camera cables:
- Using a small Phillips screwdriver, remove the two screws securing the camera bracket in place.
- Gently lift the camera bracket to expose the camera cables underneath.
- Using a plastic spudger tool or your fingers, carefully disconnect the camera cables by lifting them straight up from their connectors. Take note of their position and orientation for reassembly.
- Once the camera cables are disconnected, you can remove the camera bracket from the device.
It is important to be cautious while disconnecting the camera cables, as they are delicate and can be easily damaged. Take your time and avoid using excessive force. Once the camera cables are safely disconnected, you can proceed to the next step in replacing the rear glass camera piece of your iPhone 5s.
Step 5: Remove the camera piece from the rear glass
To replace the rear glass of your iPhone 5s, you will need to remove the camera piece from the old rear glass. Follow the steps below to do this:
- Start by gently prying the camera piece away from the adhesive on the rear glass using a plastic opening tool or a fingernail.
- Take extra care not to damage the camera lens or the surrounding components as you separate the camera piece from the rear glass.
- If the adhesive is too strong, you can use a hairdryer to warm up the rear glass slightly. This will help loosen the adhesive and make it easier to remove the camera piece.
- Once the camera piece is detached from the rear glass, set it aside in a safe place.
- You should now have successfully removed the camera piece from the rear glass of your iPhone 5s.
Note: Handle the camera piece with care to avoid any damage. It is a delicate component that is crucial for capturing photos and videos on your iPhone.
Step 6: Install the new camera piece
Before beginning this step, make sure you have the new camera piece ready. It should be a replacement part specifically designed for the iPhone 5s rear camera.
1. Carefully remove the adhesive backing from the new camera piece, exposing the sticky side.
2. Align the new camera piece with the opening on the back of the iPhone 5s. Make sure that the lens is in the correct position and the connectors are aligned with the corresponding slots.
3. Gently press the camera piece into place, applying even pressure to ensure a secure fit.
4. Once the camera piece is properly installed, make sure it lies flat against the back of the iPhone 5s.
5. Double-check that all the connections are securely in place and that the camera piece functions correctly.
6. If everything looks good, proceed to the next step to reassemble your iPhone 5s.
Note: It is important to handle the new camera piece with care, as it is a delicate component. Avoid touching the lens or any sensitive parts during the installation process.
FAQ
What tools do I need to replace the rear glass camera piece on iPhone 5s?
To replace the rear glass camera piece on iPhone 5s, you will need the following tools: a small Phillips screwdriver, a pentalobe screwdriver, a plastic opening tool, a suction cup, tweezers, and a replacement rear glass camera piece.
Is it difficult to replace the rear glass camera piece on iPhone 5s?
Replacing the rear glass camera piece on iPhone 5s can be a bit challenging, especially if you have never done it before. It requires some technical skill and patience. However, with the right tools and a step-by-step guide, it is definitely doable for most people.
Can I replace the rear glass camera piece on iPhone 5s myself, or should I take it to a professional?
While it is possible to replace the rear glass camera piece on iPhone 5s yourself, it is recommended to take it to a professional if you are not confident in your technical skills. This will ensure that the replacement is done correctly and avoid any further damage to your device. However, if you are comfortable with electronics and have the right tools, you can give it a try yourself.
