How to remove iphone 6 rear camera lens cover

Is your iPhone 6 rear camera lens cover scratched or damaged? If so, you may be experiencing blurry or distorted photos. Don’t worry, though, because replacing the lens cover is a relatively simple process that you can do yourself. In this article, we will guide you through the steps to remove the rear camera lens cover on your iPhone 6.

Step 1: Preparation

Before you begin, make sure you have a clean and organized workspace. Gather all the tools you will need, including a small suction cup, a pointy metal spudger, and a pentalobe screwdriver. It’s also a good idea to have a soft cloth or microfiber towel handy to protect your iPhone’s screen during the process.

Step 2: Removing the Rear Panel

Start by powering off your iPhone 6. Once it is turned off, locate the two pentalobe screws at the bottom edge of the phone. Use the pentalobe screwdriver to carefully unscrew these screws. Then, place the suction cup near the Home button and gently pull upward, creating a small gap between the rear panel and the rest of the device. Insert the metal spudger into the gap and run it along the edge to loosen the adhesive holding the rear panel in place.

Spy-Fy iPhone 13 Pro Case with Camera Covers Front and Rear | Protect Your iPhone and Privacy | 6-Foot Drop Proof | 6,1 Inch | Camera Protection by Valenta. Black
Spy-Fy iPhone 13 Pro Case with Camera Covers Front and Rear | Protect Your iPhone and Privacy | 6-Foot Drop Proof | 6,1 Inch | Camera Protection by Valenta....
$54.95
Amazon.com
Amazon price updated: November 11, 2024 2:06 pm

Step 3: Detaching the Camera Lens Cover

With the rear panel removed, you will now have access to the rear camera lens cover. The cover is held in place by a few small screws, which you will need to remove using the appropriate screwdriver. Once all the screws are removed, carefully lift the camera lens cover using the metal spudger. Be gentle to avoid damaging the camera lens or any other internal components.

Please note: Removing the rear camera lens cover may void your iPhone’s warranty. If your device is still under warranty, it is recommended to have it serviced or repaired by a professional technician.

By following these steps, you will be able to remove the rear camera lens cover on your iPhone 6 and replace it with a new one. Remember to handle all the components with care and take your time to ensure a successful repair. Good luck!

Step 1: Gather the necessary tools

Before you begin the process of removing the rear camera lens cover on your iPhone 6, it is important to gather all the necessary tools. Having the right tools will make the process easier and help prevent any damage to the device. Here is a table listing the tools you will need:

CADeN Camera Backpack Bag for DSLR/SLR Mirrorless Camera Waterproof with 15.6 inch Laptop Compartment, USB Charging Port, Tripod Holder, Rain Cover, Camera Case Compatible for Sony Canon Nikon Black L
CADeN Camera Backpack Bag for DSLR/SLR Mirrorless Camera Waterproof with 15.6 inch Laptop Compartment, USB Charging Port, Tripod Holder, Rain Cover, Camera...
$59.99
Amazon.com
Amazon price updated: November 11, 2024 2:06 pm
Tool Description
Small Phillips screwdriver This screwdriver is used to remove the screws holding the rear camera lens cover in place. Make sure it is the correct size to fit the screws on your iPhone 6.
Plastic opening tool This tool is used to safely pry open the back cover of your iPhone 6 without scratching or damaging it.
Tweezers Tweezers can be handy for handling small parts or screws that may be difficult to pick up with your fingers.
Cleaning cloth A soft and lint-free cleaning cloth is necessary to clean the camera lens cover and the device before reassembling it.
Replacement camera lens cover If you are planning to replace the damaged lens cover, make sure you have a compatible replacement ready.

Having these tools ready before starting the process will ensure that you have everything you need and can proceed smoothly with removing the rear camera lens cover on your iPhone 6.

Step 2: Power off your iPhone 6

Before you start removing the rear camera lens cover on your iPhone 6, it is important to power off the device to avoid any potential damage or accidents.

To power off your iPhone 6, follow these steps:

  1. Press and hold the power button located on the top right side of your iPhone.
  2. After a few seconds, the “slide to power off” option will appear on your screen.
  3. Swipe the slider from left to right to power off your iPhone.
See also  Does iphone 12 pro have wide angle camera

Alternative Method:

If your iPhone 6 is unresponsive or the screen is not working, you can use the alternate method to power off your device:

  1. Press and hold the power button along with the home button located on the front of your iPhone simultaneously.
  2. Continue holding both buttons until the Apple logo appears on the screen.
  3. Once the Apple logo appears, release both buttons and your iPhone will power off.

Now that your iPhone 6 is powered off, you can proceed to the next step in removing the rear camera lens cover.

Cwatcun Camera Backpack Professional DSLR Bag with USB Charging Port Rain Cover, Photography Laptop Backpack for Women Men Waterproof, Camera Case Compatible for Sony Canon Nikon Lens Tripod (Black)
Cwatcun Camera Backpack Professional DSLR Bag with USB Charging Port Rain Cover, Photography Laptop Backpack for Women Men Waterproof, Camera Case Compatible...
$59.99
Amazon.com
Amazon price updated: November 11, 2024 2:06 pm

Step 3: Remove the two pentalobe screws

Before you can remove the rear camera lens cover on your iPhone 6, you will need to remove the two pentalobe screws located at the bottom of the device. These screws hold the rear housing in place.

Using a pentalobe screwdriver, carefully unscrew the two screws. Make sure to apply gentle pressure and keep the screwdriver aligned with the screw head to avoid stripping the screws. Place the screws in a safe location, as you will need them later for reassembly.

Once the screws are removed, you can proceed to the next step.

Step 4: Use a suction cup to lift the rear panel

Once you have removed the two Pentalobe screws, it’s time to use a suction cup to lift the rear panel. The suction cup will create a seal on the back of the iPhone, allowing you to pull up the panel. Make sure the surface of the rear panel is clean and free from any debris, as this will ensure a stronger seal.

Place the suction cup near the Home button or the bottom edge of the rear panel. Press firmly to create a good seal between the suction cup and the panel. Once the suction cup is securely attached, gently pull up the suction cup to lift the rear panel away from the rest of the iPhone.

PRUVEEO Mirror Dash Cam Front and Rear, Dual Dashcam 1080P Backup Rear View Camera,10 inch Full Touch Screen, Loop Recording, G-Sensor, Parking Monitor 170° Wide Angle (J12)
PRUVEEO Mirror Dash Cam Front and Rear, Dual Dashcam 1080P Backup Rear View Camera,10 inch Full Touch Screen, Loop Recording, G-Sensor, Parking Monitor 170°...
$59.99
Amazon.com
Amazon price updated: November 11, 2024 2:06 pm

Be careful not to pull too hard or too quickly, as this could cause damage to the rear panel or the internal components of the iPhone. Apply steady and even pressure to gradually lift the panel.

It’s important to note that some iPhone models may require additional tools or steps to successfully remove the rear panel. Refer to the specific instructions for your iPhone model to ensure you follow the correct procedure.

Step 5: Disconnect the battery connector

Before proceeding further, it is crucial to disconnect the battery connector to ensure your safety and prevent any potential damage. This step is important because it will power off the device and minimize the risk of electrical shock.

Step 5.1: Gather necessary tools

First, gather the necessary tools required for this step:

  • Small Phillips screwdriver
  • Spudger tool

Step 5.2: Open the device

Hold the device securely and locate the two pentalobe screws on either side of the charging port. Use the small Phillips screwdriver to remove these screws.

Kase Revolution 95mm Universal Magnetic Lens Stack Front & Rear Cap Kit fits Wolverine, Revolution & Skyeye
Kase Revolution 95mm Universal Magnetic Lens Stack Front & Rear Cap Kit fits Wolverine, Revolution & Skyeye
$60.00
Amazon.com
Amazon price updated: November 11, 2024 2:06 pm

Once both screws have been removed, gently separate the display assembly from the rear case using the spudger tool. Be careful not to damage any of the delicate components or cables.

Step 5.3: Disconnect the battery connector

Locate the battery connector, which is a small white rectangle with a red cable attached. To disconnect it, use the spudger tool or your fingernail to carefully lift the connector straight up from its socket.

Take your time during this step and ensure that you only lift the connector and not the socket. Applying excessive force or tilting the connector may damage it or the logic board.

Once the battery connector is disconnected, set the display assembly aside while you continue with the repair process.

See also  Is iphone 6s camera better than 13mp

Note: It is crucial to avoid any unnecessary contact with the battery connector pins or the exposed logic board components. Accidental contact could result in short circuits or damage to the device.

LensCoat Raincoat RS for Camera and Lens, Large Rain Cover Sleeve Camouflage Protection (Realtree Max4 HD) LCRSLM4
LensCoat Raincoat RS for Camera and Lens, Large Rain Cover Sleeve Camouflage Protection (Realtree Max4 HD) LCRSLM4
$77.25
Amazon.com
Amazon price updated: November 11, 2024 2:06 pm

Step 6: Remove the rear camera lens cover

Once you have removed the three screws holding the rear camera module in place, you can carefully lift the camera module out of its housing. Be sure to support it with your fingers to prevent it from falling or getting damaged.

The rear camera lens cover is a small, circular piece of glass located on the back of the camera module. To remove it, you’ll need to use a tool such as a small flathead screwdriver or a pry tool.

Insert the tool between the camera lens cover and the camera module housing. Gently apply pressure to pry the lens cover away from the housing. Be careful not to apply too much pressure or you may crack or damage the lens cover or the camera module. Slowly work your way around the lens cover, loosening it from the housing.

Once the lens cover is loose, you can carefully lift it off the camera module. Set it aside in a safe place where it won’t get damaged.

At this point, you have successfully removed the rear camera lens cover from your iPhone 6. You can now proceed with any necessary repairs or replacements, or simply clean the lens cover before reassembly.

Nextbase Series 2 Additional Rear-View Dash Cam - Easy Click in Setup, Compatible w/ 322GW, 422GW, 522GW, 622GW Dash Camera Models - Ultra HD, 30° Telephoto Lens, Modular Installation
Nextbase Series 2 Additional Rear-View Dash Cam - Easy Click in Setup, Compatible w/ 322GW, 422GW, 522GW, 622GW Dash Camera Models - Ultra HD, 30° Telephoto...
$99.99
$89.99
Amazon.com
Amazon price updated: November 11, 2024 2:06 pm

Step 7: Clean the camera lens cover and surrounding area

Now that you have successfully removed the rear camera lens cover of your iPhone 6, it’s important to clean it and the surrounding area to ensure optimal camera performance. Follow these steps:

Gather the necessary materials

Before you begin cleaning, gather the following materials:

  • A microfiber cloth or lens cleaning wipes
  • A cleaning solution specifically designed for camera lenses, or isopropyl alcohol

Clean the lens cover

Take the microfiber cloth or lens cleaning wipe and gently wipe the camera lens cover in a circular motion. Be sure to remove any fingerprints, smudges, or dirt that may have accumulated on the surface. Avoid using excessive force or abrasive materials that could scratch or damage the cover.

If there are stubborn stains or dirt, you can apply a small amount of cleaning solution specifically designed for camera lenses or isopropyl alcohol to the cloth or wipe. Again, gently clean the lens cover in a circular motion until the stains are removed.

Clean the surrounding area

In addition to cleaning the lens cover, it’s also important to clean the area around the camera to ensure no dust or debris obstructs the lens. Use the same microfiber cloth or lens cleaning wipe to gently wipe the area surrounding the lens. Pay attention to the edges and corners where dust particles may accumulate.

If you notice any stubborn dirt or debris, you can use a soft brush or a clean, dry toothbrush to gently dislodge and remove it.

Once you have cleaned the camera lens cover and the surrounding area, make sure there are no cleaning solution residues or lint left behind. Inspect the lens cover for any remaining smudges or dirt and repeat the cleaning process if necessary.

By properly cleaning the camera lens cover and surrounding area, you will ensure that your iPhone 6’s camera can capture clear and crisp photos and videos.

Step 8: Reassemble your iPhone 6

Once you have successfully replaced the rear camera lens cover on your iPhone 6, it’s time to reassemble the device. Follow these steps to put your iPhone 6 back together:

  1. Take the front screen assembly and carefully align it with the rear case.
  2. Press the front screen assembly firmly onto the rear case to ensure a secure fit.
  3. Reinsert the screws that secure the front screen assembly to the rear case. Make sure to tighten them, but be careful not to overtighten.
  4. Attach the display connectors to the logic board, making sure they are fully seated.
  5. Reconnect the battery flex cable to the logic board.
  6. Carefully insert the rear camera into its housing, ensuring it is properly aligned.
  7. Secure the rear camera with the screw you removed earlier.
  8. Place the SIM card tray back into its slot, and make sure it is flush with the device.
  9. Finally, replace the rear case screws, making sure they are tightened securely.
See also  Is iphone camera night mode worth it

Once you have completed these steps, your iPhone 6 should be fully reassembled and ready to use. Double-check that all components are properly connected and secure before powering on your device. If you encounter any issues or difficulties during the reassembly process, it’s recommended to seek professional assistance or consult the official Apple support documentation.

Step 9: Power on your iPhone 6

Once you have successfully replaced the rear camera lens cover, it is time to power on your iPhone 6 and check if everything is working properly.

Press and hold the power button located on the right side of your iPhone until the Apple logo appears on the screen. This may take a few seconds.

Once your iPhone 6 has powered on, unlock the device using your passcode or Touch ID (if enabled).

Navigate to the camera app and test the functionality of the rear camera. Take a few photos or record a video to ensure that the new lens cover is working correctly.

If you notice any issues or the camera is not functioning properly, double-check that the lens cover is correctly installed and try again. If the problem persists, consult a professional technician for further assistance.

Important Note:

Make sure to power off your iPhone 6 before attempting any repairs or replacements, and follow all safety procedures to avoid damage to the device or personal injury.

FAQ

Can I remove the rear camera lens cover of my iPhone 6? How can I do it?

Yes, you can remove the rear camera lens cover of your iPhone 6. To do so, you will need a small Phillips screwdriver and a suction cup. First, turn off your iPhone and remove the two screws located on either side of the lightning port. Next, use the suction cup to pull up the display assembly, being careful not to apply too much pressure. Once the display assembly is lifted, you will be able to access the rear camera lens cover. Gently remove it using a pair of tweezers or a spudger, and then replace it with a new one if necessary.

Is it possible to replace the rear camera lens cover of my iPhone 6 without any tools?

No, it is not possible to replace the rear camera lens cover of your iPhone 6 without any tools. You will need a small Phillips screwdriver and a suction cup to remove the necessary screws and lift up the display assembly. Additionally, a pair of tweezers or a spudger will be required to gently remove the old lens cover and replace it with a new one if needed.

What should I do if I accidentally break the rear camera lens cover while trying to remove it from my iPhone 6?

If you accidentally break the rear camera lens cover while trying to remove it from your iPhone 6, you will need to replace it with a new one. You can purchase a replacement lens cover online or at a third-party repair shop. Follow the same steps as mentioned earlier to remove the broken lens cover and install the new one. Be sure to handle the camera lens cover with care to avoid any further damage.

John Holguin
John Holguin

Certified travel aficionado. Proud webaholic. Passionate writer. Zombie fanatic.

LensGearPro
Logo