John Holguin
FEIT is a well-known brand when it comes to outdoor security cameras. Their flood light security camera offers a great solution for monitoring your property and ensuring its safety. However, there may be times when you need to reset the camera to its factory settings, whether it’s due to technical issues or if you’re planning to sell or give it away.
Resetting the FEIT flood light security camera is a relatively simple process that can be done in just a few steps. By following the instructions below, you’ll be able to reset your camera and start fresh.
Step 1: Locate the reset button on the camera. This button is usually small and can be found either on the side or on the bottom of the camera. It may be labeled as “RESET” or have a small circular arrow symbol.
Step 2: Press and hold the reset button for approximately 10 seconds. You may need to use a small tool such as a paperclip or a pen to press the button. Make sure to apply steady pressure and hold it for the full duration.
Step 3: Release the reset button after 10 seconds. You may notice that the camera’s LEDs will start to flash or turn off and on. This is an indication that the camera is being reset.
Step 4: Wait for the camera to finish resetting. This process may take a few minutes, so it’s important to be patient and allow the camera to complete the reset on its own.
Once the FEIT flood light security camera has finished resetting, it will return to its factory settings. You can then proceed with the initial setup process, including connecting it to your Wi-Fi network and configuring any desired settings.
Note: Resetting the camera will erase any previous configuration, including saved footage and settings. Make sure to backup any important data before proceeding with the reset.
By following these simple steps, you can easily reset your FEIT flood light security camera and ensure that it is ready for use again. Remember to consult the camera’s user manual or contact FEIT customer support if you encounter any difficulties during the reset process.
Overview of Feit Flood Light Security Camera
The Feit Flood Light Security Camera is a high-quality outdoor security camera that is integrated into a flood light. It is designed to provide 24/7 surveillance and monitoring of your property, ensuring the safety and security of your home or business.
With its advanced features and robust design, the Feit Flood Light Security Camera offers a reliable and effective solution for outdoor security. It is equipped with high-definition video recording and live streaming capabilities, allowing you to keep an eye on your property from anywhere, at any time.
The camera is easy to install and can be connected to your existing Wi-Fi network, enabling seamless integration with your smartphone or tablet. It also features motion detection technology, which alerts you whenever any movement is detected, ensuring that you are always aware of any potential threats.
In addition to its security features, the Feit Flood Light Security Camera also functions as a traditional flood light, providing bright and efficient lighting for your outdoor spaces. It features adjustable settings, allowing you to customize the brightness and range of the light according to your preferences.
The Feit Flood Light Security Camera combines convenience, functionality, and security in one device, making it an ideal choice for anyone looking to enhance the safety of their property. Whether you need to monitor your home or business, this camera provides peace of mind and reliable surveillance.
Why you may need to reset your Feit Flood Light Security Camera
Resetting your Feit Flood Light Security Camera may be necessary for various reasons. Here are a few common situations where a reset might be required:
1. Technical issues: If your camera is experiencing connectivity issues, freezing, or other technical problems, resetting it could help resolve these issues. Resetting allows the device to start fresh, eliminating any potential glitches or conflicts that may have occurred.
2. Forgotten or lost password: If you have forgotten the password for your Feit Flood Light Security Camera, performing a reset will allow you to regain access to the device. Keep in mind that resetting the camera will delete all saved settings, so you will need to set it up again after the reset.
3. Change of Wi-Fi network: If you have changed your Wi-Fi network or moved your camera to a new location with a different network, you will need to reset the camera. This will allow you to connect it to the new Wi-Fi network and ensure proper functionality and video streaming.
4. Troubleshooting steps: In some cases, when faced with troubleshooting steps from the manufacturer or technical support, a reset may be recommended to rule out any software or configuration-related issues. It’s always a good idea to perform a reset as part of the troubleshooting process.
5. Selling or giving away the camera: If you plan to sell or give away your Feit Flood Light Security Camera, resetting it is essential to protect your privacy. Resetting the camera will delete all personal settings and data, ensuring that the new owner starts with a clean slate.
6. Routine maintenance: Some users choose to perform periodic resets on their cameras as a maintenance measure. This helps keep the device running smoothly by clearing any temporary files, memory leaks, or other software-related issues that may affect performance over time.
Remember that resetting your Feit Flood Light Security Camera will erase all saved settings, so it is crucial to have any necessary information, such as Wi-Fi network credentials, available before performing a reset. Always refer to the camera’s user manual or manufacturer’s guidelines for specific instructions on how to reset your particular model.
Step-by-step guide to resetting your Feit Flood Light Security Camera
If you’re experiencing issues with your Feit Flood Light Security Camera, resetting it may help resolve the problem. Follow these steps to reset your camera:
Step 1: Disconnect the power
Before attempting to reset your Feit Flood Light Security Camera, ensure that it is not receiving any power. Locate the circuit breaker or power source connected to the camera and switch it off.
Step 2: Remove the camera from the mounting bracket
Once the power is disconnected, carefully remove the Feit Flood Light Security Camera from the mounting bracket. This can be done by loosening the screws or bolts that hold the camera in place.
Step 3: Locate the reset button
On the back or bottom of the camera, you will find a small reset button. It is usually recessed to prevent accidental resets. Use a small pointed object, such as a pen or paperclip, to press and hold the reset button.
Step 4: Power on the camera and continue holding the reset button
While still holding the reset button, reconnect the power source to the Feit Flood Light Security Camera. You can switch on the circuit breaker or power source again. Make sure to keep pressing and holding the reset button throughout this process.
Step 5: Wait for the LED indicators
As the camera powers on, you will notice the LED indicators starting to flash. Continue holding the reset button until the LEDs stop flashing and remain steady. This usually takes around 10-15 seconds.
Step 6: Release the reset button
Once the LED indicators have stabilized and are no longer flashing, release the reset button.
Step 7: Reinstall the camera
Now that your Feit Flood Light Security Camera has been successfully reset, you can reinstall it on the mounting bracket. Secure the camera in place using the screws or bolts you removed earlier.
Note: Resetting your Feit Flood Light Security Camera will erase all previous settings and configurations. You will need to set it up again as if it was a new camera.
Following these steps should help you reset your Feit Flood Light Security Camera and resolve any issues you may be experiencing. If the problem persists, consider contacting Feit support for further assistance.
Gather the necessary tools and materials
Before resetting your Feit floodlight security camera, it’s important to gather all the necessary tools and materials to ensure a smooth process. Here is a list of items you will need:
1. Screwdriver
A screwdriver will be needed to remove the screws holding the floodlight camera in place. Depending on the model, you may need a Phillips or flathead screwdriver.
2. Ladder or Step Stool
Since the floodlight camera is typically mounted at a higher position, you will need a ladder or step stool to access it. Ensure that the ladder or step stool is stable and secure before climbing.
3. Power Source
Make sure you have access to a power source to plug in the floodlight camera after resetting it. This can be an outdoor electrical outlet or any other appropriate power source nearby.
4. Mobile Device or Computer
You will need a mobile device (such as a smartphone or tablet) or a computer with Wi-Fi capabilities to configure the reset floodlight camera. Ensure that the device is fully charged or connected to a power source during the process.
5. Internet Connection
An active internet connection is necessary to connect the reset floodlight camera to a network. Make sure you have a stable and reliable internet connection before proceeding with the reset.
Having these tools and materials ready will help you facilitate the reset process and ensure a successful reset of your Feit floodlight security camera.
Disconnect the power source
Before attempting to reset your Feit flood light security camera, it is important to disconnect the power source. This will help ensure your safety and prevent any electrical damage.
To disconnect the power source, follow these steps:
- Locate the circuit breaker: Start by finding the circuit breaker that controls the power supply for the flood light security camera. This is typically located in your main electrical panel or a sub-panel.
- Identify the correct breaker: Look for the breaker that is labeled or identified as the one controlling the power to the flood light security camera. If you are not sure which breaker it is, you may need to test each one individually or consult an electrician.
- Turn off the breaker: Once you have identified the correct breaker, flip it to the “Off” position. This will cut off the power supply to the flood light security camera.
- Verify power is off: To make sure the power is truly disconnected, try turning on the flood light security camera or any other nearby devices that are powered by the same circuit. If they do not turn on, it means the power is successfully disconnected.
By disconnecting the power source, you can safely proceed with the reset process for your Feit flood light security camera. This will help ensure that the camera resets properly and any issues are resolved effectively.
Remove the camera from its mount
To reset the Feit flood light security camera, you will need to remove it from its mount. Follow the steps below:
- Turn off the power: Firstly, ensure that the power to the camera is switched off. This is crucial for your safety and to avoid any electrical mishaps during the process.
- Remove the camera housing: Carefully unscrew the camera housing from the mount. Most Feit flood light security cameras have a housing that can be easily detached. Use a screwdriver if necessary, and make sure to hold onto the housing so that it doesn’t fall.
- Disconnect the cables: Next, disconnect any cables that are connected to the camera. This includes the power cable and any Ethernet cables that may be present. Double-check that all cables are disconnected before proceeding.
- Detach from the mount: Gently slide the camera off the mount. Depending on the type of mount used, you may need to use a twisting or sliding motion to detach the camera from the mount. Take your time and be cautious not to damage the camera or the mount during this step.
Note: It is recommended to consult the Feit flood light security camera’s user manual for specific instructions on removing the camera from its mount, as different models may have slightly different methods.
Reset the camera to factory settings
Resetting the Feit floodlight security camera to its factory settings is a straightforward process. Follow these steps to reset the camera:
- Locate the camera’s reset button. It is usually a small hole labeled “Reset” located on the back or the underside of the camera.
- Using a small tool or a paperclip, press and hold the reset button for about 10 to 15 seconds.
- Release the reset button after the specified time, and the camera will perform a factory reset.
- Wait for the camera to reboot and initialize. This process may take a couple of minutes.
After the camera has reset to its factory settings, it will be in its default configuration. You will need to set it up again using the Feit floodlight security camera app or the web interface, depending on the model.
Note that performing a factory reset will erase all the camera’s settings and configurations. Make sure to back up any important data before resetting the camera.
Reinstall the camera
If resetting your Feit flood light security camera did not solve the issue, you may need to reinstall the camera. Follow these steps to reinstall the camera:
- Remove the camera from its current location by gently disconnecting it from its mounting bracket or holder.
- Clean the mounting area to ensure a secure and clean installation.
- Inspect the camera and its cables for any damage or wear. If any damage is found, repair or replace the necessary parts before reinstalling.
- Locate a suitable mounting spot for the camera that provides the desired viewing angle and coverage.
- Mount the camera by attaching it to the bracket or holder using the provided screws or other mounting hardware.
- Ensure the camera is securely attached and tightened to prevent any movement or instability.
- Connect the camera’s cables to the appropriate ports on your security system or recorder.
- Turn on the power to the camera and check for proper functionality.
- Adjust the camera’s position and angle if necessary to optimize the viewing range.
- Test the camera’s recording and monitoring capabilities to verify that it is functioning correctly.
If you encounter any issues during the reinstallation process, consult the camera’s user manual or contact Feit customer support for further assistance.
Reconnect the power source
To reset your Feit flood light security camera, the first step is to reconnect the power source. Follow these instructions:
- Make sure that the power to the flood light security camera is turned off.
- Locate the power source, which is typically an electrical outlet or a power cable.
- If you are using an electrical outlet, ensure that it is in good condition and working properly.
- If you are using a power cable, check that it is securely connected to both the power source and the flood light security camera.
- If necessary, replace the power cable with a new one to ensure proper connection.
- Once you have confirmed that the power source is in good working condition and securely connected, turn on the power to the flood light security camera.
By reconnecting the power source, you are allowing the camera to receive the necessary power to reset and function properly.
Test the camera
Once you have reset your Feit flood light security camera, it is important to test it to ensure it is functioning properly. Follow these steps to test the camera:
1. Check the power source
Make sure the camera is properly connected to a power source. Check if the power adapter is securely plugged into the camera and the power outlet. If the camera runs on batteries, ensure they are inserted correctly.
2. Connect to the network
Ensure that your camera is connected to your Wi-Fi network. Use the camera’s mobile app or web interface to check the network settings and make sure it is connected to the correct network.
Note: If you have changed your Wi-Fi network or router, you may need to reconfigure the camera’s network settings.
3. Access the camera’s live feed
Launch the mobile app or open the web interface to access the camera’s live feed. Check if you can view the camera’s live feed on your mobile device or computer. Make sure the camera is pointed in the desired direction and adjust its position if necessary.
Note: Some cameras may have a built-in speaker and microphone, allowing you to test the audio as well.
If you encounter any issues, refer to the camera’s user manual or contact the manufacturer’s support for further assistance.
FAQ,
Will resetting my Feit flood light security camera delete all my recorded footage?
No, resetting your Feit flood light security camera will not delete the recorded footage. The reset process only restores the camera settings to their default values and does not affect the stored recordings. However, it is always a good idea to backup your important footage regularly to ensure that it is not lost in case of any unforeseen circumstances.
Can I reset my Feit flood light security camera remotely?
No, you cannot reset your Feit flood light security camera remotely. The reset button is typically located on the camera itself and needs to be physically pressed and held for the reset process to initiate. Remote resetting is not supported by most security cameras as a security measure to prevent unauthorized access to the device.
What should I do if I forget the password for my Feit flood light security camera?
If you forget the password for your Feit flood light security camera, you can reset the camera to its factory default settings. This will remove all existing configurations, including the password, and restore the camera to its original state. To perform the reset, follow the steps mentioned earlier in this article. Once the camera is reset, you can set up a new password and configure the camera as per your requirements.
