Action Camera Smartphone Super 90mm Vacuum Suction Cup Race Car Mount Holder Motion Camcorder Cab Cockpit Vehicle Windshield Hood Cab Rooftop…

On opening the package, I was looking at the go pro mount. I don’t have a go pro, so I wasn’t actually sure what this piece was, but I unscrewed the tightener a bit, then tightened it back up a bit. I did not tighten hard, and granted it was “empty” and I don’t have a go pro in it, but it immediately broke (see picture). It’s likely that if I had a go pro, I could still use the plastic piece for a friction fit, and it might not have broken had I put a go pro in there, but it’s definitely not reassuring.

The rest of this mount looks decently sturdy. The phone clip is very narrow, having a maximum expansion just barely wide enough to get around my phones (Pixel 4XL and Pixel 3XL, for example). It should be enough, but I would be somewhat wary that if I had a slightly larger phone I wouldn’t be able to fit it.

Overall, seems like it’ll do what I want, but definitely these two issues are concerning.

Had to push too much on the window so it works. And almost broke my hand trying to push the lever into position. Tried on different surfaces and it’s too hard to install. It fell a few times from a couple of windows. I’m returning it because it doesn’t work as advertised.

After it fell off for the first time, it was pretty much useless. Tried all the tricks on YouTube to help the suction cup go fully flat again before mounting and restoring full suction but it didn’t stay any longer than an hour after that. Binned it.

This mount has been frustrating from the moment I bought it. The pieces are poorly made and the base that attaches to the suction cup was manufactured in too large a size. I had to force it in because it was made too large and I nearly broke the plastic base doing so. I was able to use this for 3 racing track days. The ball joints have wing nuts that can be tightened down, but even at full tightness the wing nuts do not hold the mount in place so my camera was moving around and unstable. One of the ball joints cracked from the pressure despite the pressure not being enough to hold it stable in place. I would not recommend this product.

 I needed a mount for a camera in order to record at autocross events (drive around cones in a parking lot for the fastest time). This one was long enough to hang far enough down so that the rearview mirror is not in the way.

I was worried about shakiness from a long mount like this but take a look at the footage, it’s not bad. This was recorded with a Campark V30 at 1080p/60fps (downgraded to Amazon video quality). You can still see some high-frequency shaking especially when I hit bumps, but overall it doesn’t detract significantly from the viewing experience. For the price, it does an acceptable job.

My driving, on the other hand, is a different story – this was my 2nd event, yes I know I was taking some parts real slow!

 Was very happy when I first received the product, everything was sturdy and well made. Lots of adjustments would make it perfect for mounting to the car for some action shots. I tested it without a camera on a few smooth surfaces around the house and it seemed to work fine. I finally got my new Insta360 One R camera and wanted to try it out asap. I cleaned the surface of the car and suction cup and put the mount on the car. Everything seemed secure and I lightly pulled on the mount and it didn’t budge. I was trying to get video of the exhaust sound so I started the car in the garage and started the video from my app which means I didn’t have to touch the camera on the car. I took a 18 sec video without even moving or revving the engine, then I shut the car off. I stood behind the car while I viewed the video to see how it came out and about 30 seconds later the mount just released and fell to the garage floor. It’s like I saw it in slow motion, because the camera was below the mount the camera hit first on the corner then the mount hit and bounced so one of the lenses hit the floor. Ugh, to top it off I just found out from Insta360 that the lenses are not replaceable/repairable and I’d have to buy new dual lens module. Sorry such a long sad review just really disappointed with the mount especially considering there was no stress applied to it to cause it to release. Also disappointed with Insta360 right now, but hoping they’ll offer a better solution. Finally pic and video are distorted due to the stick line on 360 cameras, since the camera is so close to the mount the stitch line is worse.

 This product is great, it’s very sturdy, not much shaking getting picked up on video. and i feel very confident while using it.