John Holguin
Accidents happen, and sometimes the back camera glass of your iPhone 7 Plus can get cracked or shattered. Thankfully, you don’t need to replace the entire device. With a few simple steps, you can replace the back camera glass on your iPhone 7 Plus and restore it to its original condition.
First, you’ll need to gather the necessary tools for this repair. You’ll need a small suction cup, a plastic pry tool, a Phillips #000 screwdriver, and a replacement camera glass. These tools can be easily found online or at a local electronics store.
Start by powering off your iPhone 7 Plus and using the small suction cup to lift the back cover. Be careful not to apply too much pressure, as you don’t want to damage the device further. Once the back cover is lifted, use the plastic pry tool to gently separate the cover from the device.
Next, you’ll need to remove the screws holding the camera module in place. Use the Phillips #000 screwdriver to carefully remove these screws. Once the screws are removed, you can gently lift the camera module from the device. Be sure to disconnect any cables or connectors before fully removing the module.
Once the camera module is removed, you can safely remove the cracked or shattered camera glass. Take your replacement camera glass and carefully place it back into position. Ensure that it is securely in place before reattaching the camera module to the device.
Finally, reattach any cables or connectors that were disconnected earlier, and carefully reinsert the screws to secure the camera module. Once everything is securely in place, you can carefully reattach the back cover of your iPhone 7 Plus. Power on your device, and you should now have a fully functioning back camera with a new glass cover.
Replacing the back camera glass on your iPhone 7 Plus is a fairly straightforward process, but if you’re not comfortable doing it yourself, it’s always best to seek professional help. Be sure to follow any specific instructions provided with your replacement camera glass, and take your time to ensure that the repair is done correctly. With a little patience and the right tools, you can easily replace the back camera glass on your iPhone 7 Plus and have it looking as good as new.
Steps for Replacing Back Camera Glass on iPhone 7 Plus
Replacing the back camera glass on your iPhone 7 Plus can be a delicate process, but with the right tools and instructions, you can do it yourself. Follow these steps to replace the back camera glass on your iPhone 7 Plus:
- Gather the necessary tools. You will need a Phillips screwdriver, a suction cup, a plastic spudger, a hairdryer or heat gun, tweezers, and a replacement camera glass.
- Power off your iPhone 7 Plus and remove the SIM card tray.
- Apply heat to the back of the iPhone 7 Plus using a hairdryer or heat gun for about 2-3 minutes to soften the adhesive.
- Place the suction cup near the bottom edge of the back glass and gently pull up to create a small gap.
- Insert the plastic spudger into the gap and carefully slide it around the edges to loosen the adhesive.
- Use the suction cup to lift the back glass off the iPhone 7 Plus.
- Disconnect the cables connected to the camera and gently remove the back camera glass from the iPhone.
- Take the replacement camera glass and carefully place it in the proper position.
- Reconnect the cables to the camera.
- Apply gentle pressure to the back camera glass to make sure it is secured in place.
- Reassemble your iPhone 7 Plus by following the steps in reverse order.
That’s it! You have successfully replaced the back camera glass on your iPhone 7 Plus. Remember to take your time and be careful throughout the process to avoid causing any damage to your device.
Required Tools and Materials:
Before beginning the process of replacing the back camera glass on your iPhone 7 Plus, make sure you have the following tools and materials:
- Replacement back camera glass for iPhone 7 Plus
- Screwdriver set with Phillips and pentalobe screwdriver heads
- Suction cup
- Plastic pry tool
- Small tweezers
- Heat source (such as a hairdryer or heat gun)
- Cleaning cloth
- Isopropyl alcohol
- Adhesive tape or adhesive strips
Replacement Back Camera Glass:
Make sure you have the correct replacement back camera glass for your iPhone 7 Plus model. It should be specifically designed for the iPhone 7 Plus and match the dimensions and shape of the original glass.
Screwdriver Set:
You will need a screwdriver set with both Phillips and pentalobe screwdriver heads to remove the screws holding the back panel in place.
Suction Cup:
A suction cup is needed to securely grip and lift the back panel of your iPhone 7 Plus during the repair process.
Plastic Pry Tool and Small Tweezers:
A plastic pry tool and small tweezers are essential for safely prying and removing the broken camera glass from the back panel.
Heat Source:
A heat source, such as a hairdryer or heat gun, is necessary to soften the adhesive securing the camera glass to the back panel for easy removal.
Cleaning Cloth and Isopropyl Alcohol:
A cleaning cloth and isopropyl alcohol are needed to thoroughly clean the back panel and remove any residue before applying the replacement camera glass.
Adhesive Tape or Adhesive Strips:
Adhesive tape or adhesive strips are required to properly attach the replacement camera glass to the back panel of your iPhone 7 Plus.
Step 1: Prepare the Workspace
Before beginning the process of replacing the back camera glass on your iPhone 7 Plus, it’s important to create a suitable workspace. Follow these steps to ensure you have everything you need:
Gather the necessary tools
Make sure you have all the required tools for the repair. These may include a small Phillips screwdriver, a flathead screwdriver, a suction cup, a pry tool, and a microfiber cloth. Having all the tools ready before you start will save you time and make the process smoother.
Find a clean and well-lit area
Choose a location with a clean and clutter-free surface to work on. A well-lit area will help you see the small details and avoid any accidental damage. Consider using a desk or table covered with a soft cloth to protect your iPhone from scratches.
Prepare an anti-static mat or grounding strap
Static electricity can damage sensitive components of your iPhone, so it’s crucial to take precautions. Place an anti-static mat or use a grounding strap to prevent any static discharge during the repair process. This will help protect your device from any potential harm.
By taking the time to prepare your workspace properly, you’ll set yourself up for a successful back camera glass replacement on your iPhone 7 Plus. With all the necessary tools and a clean environment, you’re ready to move on to the next steps.
Step 2: Power Off the iPhone
Before starting the repair process, it is crucial to power off your iPhone to prevent any potential damage or accidents.
To power off the iPhone 7 Plus, press and hold the power button located on the right side or top of the device, depending on its orientation.
After holding the power button for a few seconds, a “slide to power off” option will appear on the screen. Slide it to the right to turn off the iPhone.
If the screen is unresponsive and you can’t slide to power off, press and hold the power button along with the volume down button simultaneously until the screen goes black.
Once the iPhone is powered off, you can proceed with the camera glass replacement without risking any damage to the device.
Step 3: Remove the Back Panel
Before proceeding with the camera glass replacement, you need to remove the back panel of your iPhone 7 Plus. Follow the steps below carefully:
Tools you will need:
- Phillips #000 screwdriver
- Plastic spudger
- Suction cup
- Tweezers
1. Power off your iPhone.
Make sure your iPhone is completely turned off before you begin the disassembly process. This is important for your safety as well as preventing any possible damage to your device.
2. Remove the two bottom screws.
Use a Phillips #000 screwdriver to remove the two small screws located on each side of the Lightning connector at the bottom of your iPhone.
3. Use a suction cup to lift the back panel.
Place a suction cup on the lower half of the back panel, just above the Home button. Apply gentle pressure to create a small gap between the panel and the iPhone frame.
Note: If the back panel is cracked or shattered, cover it with a piece of clear tape to prevent any further damage while removing it.
4. Insert a plastic spudger.
Insert a plastic spudger into the gap created by the suction cup. Gently pry the back panel upwards, moving the spudger along the sides to release the adhesive holding it in place.
5. Lift and remove the back panel.
Once the adhesive is loosened, carefully lift the back panel upwards to separate it from the iPhone 7 Plus.
Caution: Be careful not to pull the panel too far as it is still connected to the iPhone by several cables.
Now that you have successfully removed the back panel, you can proceed with replacing the camera glass on your iPhone 7 Plus.
Step 4: Disconnect the Camera Connector
Before proceeding with the camera glass replacement, it’s important to disconnect the camera connector to avoid any damage to the camera module.
- Start by turning off your iPhone 7 Plus to prevent any accidental electrical discharge.
- Using a pentalobe screwdriver, remove the two screws located at the bottom of the phone near the charging port.
- Gently slide the suction cup towards the home button end of the phone to create a slight gap between the display assembly and the rear case.
- Insert a plastic opening tool into the gap and carefully pry open the display assembly from the rear case.
- Once you’ve created enough of a gap, slide your plastic opening tool along the edge of the phone to release the clips securing the display assembly.
- Open the iPhone by swinging the display assembly up from the left side, like the back cover of a book.
- Locate the camera connector cable at the top of the phone, next to the rear camera module.
- Using a spudger or your fingernail, carefully flip up the small retaining flap on the camera connector bracket. This will release the connector cable.
- Once the retaining flap is flipped up, gently pull the camera connector straight out of its socket. Take care not to apply too much force.
- With the camera connector disconnected, you can now proceed with the replacement of the back camera glass.
Remember to follow the instructions carefully and take your time to avoid any unnecessary damage to your iPhone 7 Plus.
Step 5: Remove the Old Glass
Before you can replace the back camera glass on your iPhone 7 Plus, you’ll need to carefully remove the old glass from the device. Here are the steps to follow:
1. Prepare your workspace: Find a clean, well-lit area where you can work on your iPhone. Make sure you have all the necessary tools and materials ready.
2. Power off your iPhone: Before you begin, it’s important to turn off your iPhone completely to avoid any accidents or damage.
3. Remove the back cover: Gently loosen the two bottom screws on either side of the charging port using a pentalobe screwdriver. Place the suction cup near the home button and gently pull up to lift the back cover.
4. Disconnect the connectors: Once the back cover is lifted, you’ll see a metal plate covering the connectors. Use a Phillips screwdriver to remove the screws holding the plate in place. Carefully disconnect the connectors beneath the plate, including the one for the camera module.
5. Heat the old glass: Apply heat to the old glass using a heat gun or hairdryer to soften the adhesive. Be careful not to overheat the device.
6. Pry off the old glass: Use a plastic spudger or a pry tool to carefully lift the old glass from the device. Start from one corner and work your way around the edges, gently prying it off the frame.
7. Clean the frame: Once the old glass is removed, use a clean cloth or a microfiber cloth to wipe away any adhesive residue or debris from the frame.
8. Prepare the replacement glass: Before installing the new glass, make sure it is clean and free from any dust or fingerprints. Handle it carefully to avoid any damage.
By following these steps, you should be able to successfully remove the old glass from your iPhone 7 Plus in preparation for replacing it with a new one.
Step 6: Clean and Prepare the Frame
Before installing the new back camera glass, it is important to clean and prepare the frame of your iPhone 7 Plus. Follow these steps to ensure the best results:
| 1. | Use a microfiber cloth and gentle cleaning solution to wipe down the frame of your iPhone. |
| 2. | Make sure to remove any dirt, dust, or adhesive residue from the frame. |
| 3. | Inspect the frame for any damages or signs of wear. If necessary, consider replacing the frame before proceeding. |
| 4. | Once the frame is clean and dry, carefully remove the adhesive backing from the new back camera glass. |
| 5. | Align the new camera glass with the opening on the frame and press it down firmly to adhere it in place. |
| 6. | Double-check the alignment and make sure the camera glass is securely attached to the frame. |
By properly cleaning and preparing the frame, you will ensure that the new back camera glass will adhere correctly and provide optimal functionality. Take your time with this step to achieve the best results.
Step 7: Apply Adhesive to the Frame
Before you can attach the new camera glass, you’ll need to apply adhesive to the frame of your iPhone 7 Plus. This will ensure that the glass stays securely in place and prevents any dust or debris from getting inside.
Here’s how to apply adhesive to the frame:
- Peel off the adhesive backing on the camera glass replacement.
- Line up the camera glass with the frame and press it down firmly to secure it.
- Use a clean cloth to gently press down on the glass, ensuring it adheres to the frame completely.
It’s important to make sure the adhesive is evenly distributed and that there are no air bubbles between the glass and the frame. This will help ensure a tight seal and prevent any future issues with the camera.
Allow the adhesive to fully set and dry before reassembling your iPhone 7 Plus.
Step 8: Install the New Camera Glass
Once you have removed the old camera glass, it’s time to install the new one. Follow these steps to complete the process:
| 1. | Take the new camera glass and place it over the opening on the back of the iPhone 7 Plus. Make sure it aligns properly with the camera lens. |
| 2. | Apply gentle pressure to secure the camera glass in place. Take care not to apply too much pressure as it can crack the glass. |
| 3. | Check if the camera glass is flush with the back of the iPhone. If any part is sticking out, gently push it in until it sits properly. |
| 4. | Inspect the camera glass for any smudges or fingerprints. If necessary, use a microfiber cloth to clean it before proceeding. |
| 5. | Once everything looks aligned and clean, you can proceed to reassemble the iPhone 7 Plus by following the previous steps in reverse order. |
Congratulations! You have successfully replaced the back camera glass on your iPhone 7 Plus. Now you can enjoy clear and crisp photos without any obstructions!
Step 9: Reassemble the iPhone
Now that you have successfully replaced the back camera glass on your iPhone 7 Plus, it’s time to reassemble the device.
1. Carefully place the back cover of the iPhone onto the main body, aligning it with the camera and flash openings.
2. Gently press down on the back cover to ensure it is securely attached.
3. Next, insert the screws you had previously removed from the bottom of the device back into their respective holes.
4. Use the correct screwdriver to tighten the screws, making sure not to overtighten.
5. Once the screws are securely tightened, check the entire device for any loose parts or gaps.
6. If everything looks secure, power on your iPhone by pressing and holding the power button until the Apple logo appears.
7. After the device turns on, test the camera to ensure that it is functioning properly.
Congratulations! You have successfully reassembled your iPhone 7 Plus after replacing the back camera glass.
Step 10: Power On and Test the Camera
Once you have successfully installed the new back camera glass on your iPhone 7 Plus, it’s time to power on and test the camera to ensure everything is working properly. Here are the steps:
|
1. |
Press the power button on the right side of your iPhone to turn it on. |
|
2. |
Swipe up from the bottom of the screen to access the Control Center. |
|
3. |
Tap on the Camera icon to launch the Camera app. |
|
4. |
Switch between different camera modes (such as Photo, Video, or Portrait) to see if the back camera is functioning properly. |
|
5. |
Take a few test photos or videos to check the quality of the images and make sure there are no issues with focusing or blurry pictures. |
If you notice any problems with the camera after replacing the back camera glass, double-check your installation to ensure everything is correctly connected and aligned. If the issues persist, you may need to seek professional assistance or consider replacing the camera module entirely.
FAQ
Is it possible to replace the back camera glass on iPhone 7 Plus?
Yes, it is possible to replace the back camera glass on iPhone 7 Plus. However, it requires some technical knowledge and skill. If you are not comfortable doing it yourself, it is recommended to take it to a professional repair service.
What tools do I need to replace the back camera glass on iPhone 7 Plus?
To replace the back camera glass on iPhone 7 Plus, you will need the following tools: a small Phillips screwdriver, a pentalobe screwdriver, a spudger tool, a suction cup, a hairdryer or heat gun, and a replacement camera glass.
Can I use a hairdryer instead of a heat gun to remove the adhesive?
Yes, you can use a hairdryer instead of a heat gun to remove the adhesive. However, make sure to use it on the lowest heat setting and keep it at a safe distance from the phone to avoid overheating or damaging the device.
Where can I find a replacement back camera glass for iPhone 7 Plus?
You can find a replacement back camera glass for iPhone 7 Plus online. There are several websites and online marketplaces that sell genuine replacement parts for iPhones. Make sure to buy from a reputable seller to ensure the quality of the replacement glass.
Is it possible to replace the back camera glass without removing the entire back panel of the iPhone?
No, to replace the back camera glass on iPhone 7 Plus, you will need to remove the entire back panel of the phone. The camera glass is fixed on the back panel, and it cannot be replaced without removing it. It is a delicate process, so it is recommended to follow a step-by-step guide or watch a tutorial before attempting to do it yourself.
