John Holguin
The iPhone 6s Plus is a popular smartphone known for its advanced camera capabilities. However, there may be situations where you need to remove the front-facing camera of your iPhone 6s Plus. Whether you want to replace a faulty camera or clean the lens, removing the front-facing camera is a relatively simple process.
Before you begin, it’s important to note that removing the front-facing camera yourself may void your warranty. If your iPhone is still covered by warranty, it’s recommended to take it to an authorized service center for repairs. However, if you’re confident in your technical skills and want to take on the task yourself, here’s a step-by-step guide on how to remove the front-facing camera of your iPhone 6s Plus.
Please proceed with caution and at your own risk. Ensure that you have the necessary tools and a clean, well-lit workspace before attempting any repairs.
Replacing the front facing camera on your iPhone 6s Plus
If you’re experiencing issues with the front facing camera on your iPhone 6s Plus, such as blurry images or a camera that won’t work at all, you may need to replace the camera module. While this may seem like a daunting task, with the right tools and a bit of patience, you can easily replace the front facing camera on your iPhone 6s Plus.
Before you begin, make sure you have the necessary tools:
| 1. | Small Phillips screwdriver |
| 2. | Pry tool or plastic opening tool |
| 3. | Replacement front facing camera module |
Once you have the tools ready, follow these steps to replace the front facing camera:
- Power off your iPhone 6s Plus and remove the two screws located at the bottom of the phone using a small Phillips screwdriver.
- Use a pry tool or plastic opening tool to carefully separate the screen from the body of the phone. Start from the bottom and work your way around the edges, being careful not to apply too much pressure.
- Once the screen is lifted slightly, you can use a suction cup to gently lift it further.
- Locate the front facing camera module near the top of the phone.
- Use a small Phillips screwdriver to remove the two screws securing the front facing camera module in place.
- Carefully disconnect the ribbon cable attached to the camera module by gently lifting it with a plastic opening tool.
- Remove the old front facing camera module and replace it with the new one.
- Reconnect the ribbon cable and secure the new front facing camera module with the two screws.
- Carefully place the screen back onto the body of the phone and press down firmly to secure it in place.
- Replace the two screws at the bottom of the phone.
- Power on your iPhone 6s Plus and test the front facing camera to ensure it is working properly.
By following these steps, you can successfully replace the front facing camera on your iPhone 6s Plus and restore its functionality. However, if you’re uncomfortable with performing the replacement yourself, it’s always a good idea to seek professional help from a certified technician.
Gather the necessary tools
Before you start removing the front facing camera on your iPhone 6s Plus, make sure you have the following tools:
| 1. Screwdriver: | A small screwdriver with a flat head is required to remove the screws holding the front panel in place. |
| 2. Suction cup: | A suction cup is necessary to lift the front panel and separate it from the rest of the device. |
| 3. Spudger: | A spudger is a handy tool for safely disconnecting ribbon cables and connectors without causing any damage. |
| 4. Tweezers: | Tweezers can be used to carefully remove small components or cables from tight spaces. |
| 5. Adhesive strips: | Adhesive strips are needed to secure the new front facing camera in place after replacement. |
It is important to have all these tools ready before attempting to remove the front facing camera. Using the correct tools will help you avoid damaging the device and ensure a successful repair.
Turn off your iPhone
Before attempting to remove the front-facing camera on your iPhone 6s Plus, it is essential to turn off your device to ensure your safety and prevent any potential damage.
To turn off your iPhone 6s Plus, follow these steps:
Step 1: Press and hold the Power button
Locate the Power button on the right side of your iPhone. Press and hold it until you see the Slide to power off option appear on the screen.
Step 2: Slide to power off
Using your finger, slide the power icon from left to right across the screen. This action will initiate the shutdown process of your device. Wait for a few seconds until the screen turns completely black.
Note: If your iPhone has a passcode enabled, you will need to enter it before being able to power off your device.
Once your iPhone is turned off, you can proceed with the necessary steps to remove the front-facing camera safely. Remember to handle all components of your device with care and caution to avoid any accidental damage.
Remove the display assembly
To remove the front facing camera on an iPhone 6s Plus, you will first need to remove the display assembly. Follow these steps:
- Power off the iPhone 6s Plus.
- Remove the two pentalobe screws located at the bottom of the device using a pentalobe screwdriver.
- Use a suction cup to lift the display assembly slightly away from the rear case.
- Use a plastic opening tool to gently pry open the display assembly.
- Remove the four tri-point screws that secure the display assembly cable bracket.
- Disconnect the display assembly cable bracket from the logic board.
- Disconnect the display assembly connectors from the logic board, carefully separating the display assembly from the iPhone.
With the display assembly removed, you can now access the front facing camera to remove or replace it as needed. Remember to follow these steps in reverse order to reassemble the iPhone 6s Plus after completing any repairs.
Disconnect the front camera cable
Before removing the front facing camera of your iPhone 6s Plus, it is important to disconnect the front camera cable. This cable connects the front camera assembly to the logic board of the device, allowing it to function properly.
To disconnect the front camera cable:
- Power off your iPhone by pressing and holding the power button until the “Slide to Power Off” option appears. Slide it to the right to turn off your device.
- Use a pentalobe screwdriver to unscrew the two screws located at the bottom of the device, on either side of the charging port.
- Once the screws are removed, use a suction cup to gently lift the display assembly from the rear case.
- Open the display to an angle of about 90 degrees and prop it up against something to keep it in place.
- Locate the front camera cable connector, which is a small rectangular plug located near the top of the display assembly.
- Use a spudger tool or your fingernail to carefully lift the connector’s tab. Be gentle to avoid damaging the cable or the connector.
- Once the tab is lifted, gently pull the front camera cable connector away from its socket on the logic board. Make sure to pull it straight up and avoid any unnecessary twisting or bending.
- The front camera cable is now disconnected and you can safely proceed with removing the front facing camera assembly.
Remove the front camera cable bracket
To remove the front camera cable bracket on your iPhone 6s Plus, follow these steps:
Step 1: Gather necessary tools
Before starting the process, make sure you have the following tools:
- Pentalobe screwdriver
- Phillips screwdriver
- Tweezers
Step 2: Power off and disassemble the iPhone
Power off your iPhone and remove the two pentalobe screws located at the bottom of the device. Use a suction cup to lift the front panel and carefully remove it.
Step 3: Disconnect the front camera cable
Locate the front camera cable connector on the top right side of the device. Gently lift the connector with the help of a spudger or the flat end of a screwdriver. Be cautious not to tear or damage the cable. Once the cable is disconnected, set it aside.
Step 4: Remove the bracket screws
Identify the bracket securing the front camera cable. There are two Phillips screws holding it in place. Unscrew them using the Phillips screwdriver. Keep the screws in a safe place to prevent loss.
Step 5: Remove the front camera cable bracket
With the screws removed, gently lift the bracket with your fingers or tweezers. Be careful not to damage any nearby components. Once the bracket is lifted, set it aside.
You have now successfully removed the front camera cable bracket from your iPhone 6s Plus. Take caution when handling delicate components during this process to avoid any major damage.
Remove the front camera sensor
To remove the front camera sensor on an iPhone 6s Plus, follow these steps:
- Turn off your iPhone and disconnect it from any power source.
- Use a pentalobe screwdriver to unscrew the two screws located on either side of the charging port.
- Place a suction cup near the home button and gently pull up to create a small gap between the screen and the rear case.
- Insert an opening tool or a thin plastic card into the gap and slide it along the side to separate the screen from the rear case.
- Lift the screen assembly carefully to reveal the internal components.
- Locate the front camera sensor, which is positioned on the top of the device.
- Use a spudger tool or tweezers to disconnect the flex cable that is attached to the front camera sensor.
- Remove the screws securing the front camera sensor in place.
- Gently lift the front camera sensor out of its housing.
Make sure to handle the front camera sensor and other delicate internal components with care to prevent any damage. It is recommended to follow a detailed guide or watch a tutorial video specific to your iPhone model for the most accurate instructions.
Install the new front camera sensor
Once you have obtained a replacement front camera sensor for your iPhone 6s Plus, you can proceed to install it. Follow the steps below to safely and successfully replace the faulty sensor:
Tools you will need:
- Small Phillips screwdriver
- Plastic opening tool
- Suction cup
- Tweezers
Step-by-step instructions:
- Power off your iPhone and make sure it is disconnected from any power source.
- Use the small Phillips screwdriver to remove the two screws located on both sides of the Lightning connector.
- Place the suction cup above the Home button and gently pull upward to create a small opening between the display assembly and the rear case.
- Insert the plastic opening tool into the gap and carefully slide it along the edge, separating the display assembly from the rear case. Be gentle to avoid damaging any cables.
- Open the iPhone by swinging the display assembly up from the left side, like opening a book, until it is fully open but still connected at the top.
- Use the Phillips screwdriver to remove the four screws securing the metal bracket covering the front camera sensor and earpiece speaker connectors.
- Lift the metal bracket carefully using the plastic opening tool or tweezers.
- Disconnect the front camera sensor and earpiece speaker connectors by gently lifting them away from the logic board.
- Remove the faulty front camera sensor by gently peeling it off the adhesive securing it to the display assembly.
- Take the new front camera sensor and carefully align it with the designated area on the display assembly. Press it firmly to secure it in place.
- Reconnect the front camera sensor and earpiece speaker connectors by pressing them down onto the corresponding ports on the logic board.
- Place the metal bracket back onto the connectors and securely fasten it with the four screws.
- Close the iPhone by pressing the display assembly down until it clicks into place.
- Secure the two screws on both sides of the Lightning connector using the Phillips screwdriver.
- Power on your iPhone to test the new front camera sensor.
Congratulations! You have successfully installed the new front camera sensor on your iPhone 6s Plus. Make sure to check the camera functionality to ensure everything is working properly.
| 1. | It is recommended to use adhesive strips or double-sided adhesive to secure the display assembly back to the rear case when closing the iPhone. |
| 2. | Take your time and be patient while performing the repair to avoid causing further damage to your device. |
| 3. | If you are unsure about any step, it is best to seek professional assistance or refer to official repair guides provided by Apple. |
Reassemble your iPhone
Once you have successfully removed the front-facing camera from your iPhone 6s Plus, it is time to reassemble your device. Follow the steps below to put everything back together:
1. Replace the front-facing camera module
Take the new front-facing camera module and carefully align it with the front panel of your iPhone. Make sure all the connectors are properly aligned and insert the module into its designated slot.
2. Reattach the display cables
Gently lower the display assembly onto the frame of the iPhone. Align the display cables with their respective connectors on the logic board and carefully press them into place. Make sure the connectors are properly seated.
3. Secure the display assembly
Use the screws you previously removed to secure the display assembly to the iPhone frame. Make sure to tighten the screws firmly but not too tight to avoid damaging the device.
4. Reinstall the metal plate and other components
Reinstall the metal plate that covers the display connectors and secure it with the screws. Then, reattach any other components or cables that were removed during the disassembly process, such as the battery connector and any brackets or shields.
5. Test your iPhone
Before fully reassembling your iPhone, it is important to test it to ensure all the components are functioning properly. Reconnect the battery and power on your device to check if the front-facing camera is working correctly.
Note: If you encounter any issues or if the camera is not working properly, double-check all the connectors and retrace your steps to make sure everything is properly connected.
Once you are confident that your iPhone is working correctly, you can proceed to reattach the display panel and reassemble the remaining components.
Remember to be patient and gentle throughout the reassembly process to avoid causing any damage to your iPhone 6s Plus.
Test the new front camera
After replacing the front-facing camera on your iPhone 6s Plus, it’s important to test it to ensure it is functioning correctly. Here are some steps to guide you through the testing process:
Step 1: Open the camera app
Launch the camera application on your iPhone 6s Plus by tapping on the camera icon on your home screen or swiping right from the lock screen.
Step 2: Switch to the front camera
In the camera app, you will see a camera icon with two arrows encircling it. Tap on this icon to switch to the front-facing camera.
Step 3: Capture a photo or video
Take a picture or record a short video using the front camera. You can do this by tapping the white circular button at the bottom center of the screen to take a photo or by tapping the red record button to start and stop video recording.
Step 4: Review the captured media
After capturing a photo or video, you can review it by tapping on the lower left corner of the camera app to access the thumbnail of the media. Tap on the thumbnail to view it in full-screen mode.
| Function | Expected Result |
|---|---|
| Front camera | The front camera should be active and ready to use. |
| Image capture | The captured photo should be clear and free of any distortions or abnormalities. |
| Video capture | The recorded video should be smooth and without any visual or audio issues. |
If you experience any issues with the front-facing camera during testing, it may indicate a problem with the replacement part. In such cases, it is recommended to seek professional help or contact the supplier for further assistance.
FAQ
Can I remove the front facing camera on my iPhone 6s Plus?
Yes, you can remove the front facing camera on your iPhone 6s Plus. However, it is not a recommended action as it requires technical expertise and may void your warranty.
What tools do I need to remove the front facing camera on my iPhone 6s Plus?
You will need a small Phillips screwdriver, a plastic pry tool, a suction cup, and a guitar pick or thin plastic card to remove the front facing camera on your iPhone 6s Plus.
Are there any risks involved in removing the front facing camera on my iPhone 6s Plus?
Yes, there are certain risks involved in removing the front facing camera on your iPhone 6s Plus. You may accidentally damage other components or the flex cables during the removal process. It is recommended to seek professional help or watch tutorials before attempting to remove the front facing camera yourself.
